Translations:Kwaliteitsvol digitaliseren van tekst- en beeldmateriaal/35/en: verschil tussen versies

Uit Tracks
Naar navigatie springen Naar zoeken springen
Nieuwe pagina aangemaakt met '* Scan the entire document, leaving a margin of approximately 0.5 cm around the edge to prove that the full document has been digitised. You can always remove the m...'
 
(geen verschil)

Huidige versie van 20 apr 2021 om 14:19

Informatie over bericht (bijdragen)
Dit bericht heeft geen documentatie. Als u weet waar of hoe dit bericht wordt gebruikt, dan kunt u andere gebruikers helpen door documentatie voor dit bericht toe te voegen.
Berichtdefinitie (Kwaliteitsvol digitaliseren van tekst- en beeldmateriaal)
Neem altijd volgende vuistregels in acht:
* Scan het volledige document met een rand van ongeveer een halve cm rond het document. Zo heb je het bewijs dat je het volledige document hebt gedigitaliseerd. De rand kan je later altijd nog weghalen, bv. bij een publicatie.
* Het beeld moet op ware grootte een resolutie hebben van minimum 300 ppi. Ppi staat voor pixels per inch. Dat wil zeggen dat er voor iedere inch (een Engelse afstandsmaat) van je document 300 beeldpunten worden opgenomen. Hoe meer beeldpunten, hoe hoger de scherpte en hoe meer je het beeld kan inzoomen zonder kwaliteitsverlies voor het oog. Digitaliseer je documenten waarvan je weet dat je moet kunnen inzoomen (bv. pasfoto’s of dia’s), dan is de standaardwaarde van 300 PPI niet voldoende. Wil je het document standaard 2x kunnen inzoomen, ga dan voor 600 ppi. Voor 4x uitzoomen reken je 1200 ppi, enzovoort.
* Scan of fotografeer je in kleur, ga dan voor een bitdiepte van 24 bit. Dat is het aantal bits (de nulletjes en eentjes) dat wordt gebruikt om de kleur per pixel te registreren. Hoe groter de bitdiepte, hoe groter het gamma aan kleuren dat kan worden opgeslagen.
* Scan of fotografeer je in grijswaarden, ga dan voor een bitdiepte van 8 of 16 bit.
* Zorg dat de kleur van de opnames wordt opgeslagen in een voldoende rijk kleurprofiel. Bij digitaliseringsprojecten is een RGB-kleurenprofiel gebruikelijk. In de erfgoedwereld wordt meestal geopteerd voor de kleurprofielen ECI RGB v2 of Adobe RGB. Een veel voorkomend kleurprofiel is sRGB. Gebruik dit niet voor je archiverings- of moederbestanden (zie onder). Het gamma van kleuren dat sRGB kan opslaan is niet rijk genoeg. Voor meer informatie over kleurenprofielen, zie [[Wat zijn kleurprofielen?]].
  • Scan the entire document, leaving a margin of approximately 0.5 cm around the edge to prove that the full document has been digitised. You can always remove the margin again later, e.g. for publication.
  • The image must have a resolution of minimum 300 ppi at full size (ppi stands for ‘pixels per inch’). This means that 300 pixels are recorded for every inch of your document. The more pixels there are, the sharper the image is and the more you can zoom in without losing quality. If you’re digitising documents that you know it must be possible to magnify (e.g. passport photos and slides), the standard value of 300 ppi is not sufficient. If you want to magnify the document 2x as standard, choose 600 ppi. And use 1200 ppi to zoom in 4x, and so on.
  • If you’re scanning or taking photographs in colour, choose a bit depth of 24 bit. This is the number of bits (zeros and ones) used to register the colour per pixel. The greater the bit depth, the greater the range of colours that can be saved.
  • If you’re scanning or taking photographs in grey tones, choose a bit depth of 8 or 16 bit.
  • Make sure the colours are captured and saved using a sufficiently rich colour profile. An RGB colours profile is usual for digitisation projects. The world of heritage mostly opts for the colour profiles ECI RGB v2 or Adobe RGB. Another common colour profile is sRGB. But do not use this for your archive or master files (see below) as the range of colours that sRGB can save is not rich enough.